Outline of Piping Design: Basic Elements

The scope of Piping Design

The scope of piping design refers to the entire design process of connecting the equipment using appropriate piping components as determined by the process engineering team. It’s comparable to the human body; piping is equivalent to the veins that connect the main organs together.

The basic elements of Piping Design

The main aim of the piping design is to lay equipment, piping, and other accessories meeting the relevant standards, statutory regulations, and safety requirements. Of course, there are other aspects as described below.

Plant Layout

  • Safety: Fire, Leakage, Easy escape, safety showers, eyewash
  • Maintainability & Operability: Dropdown zone, crane, fork-lift, hose station, platform, ladder, stair
  • Cost: Economic layout (equipment/ piping), optimization of materials
  • Constructability: Transporting and erecting large equipment, space for fabrication, the sequence of construction
  • Others: Weather conditions, Wind Direction, Location, Relevant regulations, Product in/out, Utilities and drain location, Conditions around battery limit, Area for future expansion

First Piping Engineers produce Site Plan, then they develop the overall Plot Plan and Unit Plot Plans. After Unit Plot Plans are in place, They develop major piping in and around equipment. They do plan for pipe racks as well.

  • Pipe routing studies and Nozzle /platform/ladder orientations are developed.
  • Underground piping is given priority as the construction starts from underground.
  • Based on the size, temperature, pressure, flow type, and equipment type to which the line is connected, we identify lines to be Stress Analyzed. We perform Stress Analysis using software like CAESAR II, AutoPIPE, etc.
  • Pipe Routing Studies
  • Equipment Nozzle Orientation:

Underground Piping

Underground piping refers to pipes that are buried underground and it aims to optimize the design and construction processes of a plant by finding the most effective connection between each process and different utilities.

Scope of Underground Piping:

  • Underground piping routes (e.g. cooling water, sewer piping, trench piping)
  • Equipment foundation location
  • Underground electrical and instrument routes
  • Civil/structure-related information
  • Road layout, etc.
READ  Water Hammer Basics in Pumps for Beginners

Water Hammer Analysis:

What is Water Hammer?

The rise or fall in pressure caused by changes in the volume of fluid must be analyzed and applied precisely to piping design. In general, such changes in water pressure are generally known as water hammer but to be precise, hydraulic transient would be more correct. Such changes in pressure produce noise, vibration, shock, etc., which can result in the breakdown of the equipment and piping.

Main Purpose of Water hammer Analysis

3D Modeling and Review

3D Model:  Graphic data of various structures, equipment, piping, cables, and building parts of a plant displayed in virtual space using 3D CAD.

Model Review: A process carried out in-appropriate design stages to examine whether the developing work is meeting the requirements of the client and recommended design standards. It is also done to understand and provide solutions for problems in the design.

Purpose of Model Review:

Client’s Perspective

  • To ensure a quality product
  • To ensure safety
  • To examine operability
  • To examine repair/maintenance
  • To examine environmental impacts

Engineering Company’s Perspective

  • To meet the client’s requirements
  • To prevent design errors
  • To achieve better drawing quality
  • To follow drawings and construction schedules
  • To improve earnings and provide client satisfaction

Stages of Model Review:

  • 30% Model review: Review from a plot plan point of view – location, installation, construction, maintenance, and repair of the equipment
  • 60% Model review: Review from an operation point of view – process requirements, tray routes for piping. Also, make appropriate changes from the 30% review. Major Line Routing reviewed and finalized.
  • 90% Model Review: Overall review aimed at producing the final drawings. Make appropriate changes from 30% and 60% Model Reviews.
READ  Types of Lines in Engineering Drawing

Required Input for Piping Design: Workflow

  • Required Input: It ranges from PFD/P&ID, Line List, Data Sheets, and Vendor Prints to the various deliverables of other disciplines like Structural Arrangement Drawings, Cable Layout, Level sketches of Instrumentation, etc.
  • Piping Activities: Preparing Site Plan, Overall Plot Plan, Unit Plot Plan, Nozzle Orientation, Rack sizing, Equipment/ Piping modeling, Laying outlines, Job instruction, Project Specification, Materials Take Off (MTO), Stress Analysis, etc.
  • Piping Outputs: Site Plan, Overall Plot Plan, Unit Plot Plan, Nozzle Orientation, Complete 3D model, Isometrics, Pipe MTO, Project Specifications, Piping GA drawings, Special Pipe Support Index/ datasheet, Support MTO, Insulation/ Paint MTO.

It’s an IPO cycle as shown in figure (Fig. 1) below:

The IPO Cycle
Fig. 1: The IPO Cycle

Importance of statutory requirement in piping design

Statutory and Regulatory Requirements in Piping Designs….

  • When a plant is set up in any country, its design is governed by the statutory and regulatory requirements of that country. Some examples are as follows:
  • Petroleum and Explosive Safety Organisation (PESO): With an overall objective of ensuring the safety and security of public and property from fire and explosion, PESO as a statutory authority is entrusted with the administration of the Explosives Act, 1884, Petroleum Act, 1934; Inflammable Substances Act, 1952 and other related acts.
  • Oil India Safety Directorate(OISD): e.g. OISD-STD-118-Layout for Oil & Gas Installations, OISD-STD-117- Fire Protection Facilities for Petroleum Depot/ terminals, etc.
  • Indian Boiler Regulation (IBR): IBR approval is required for IBR equipment and lines.
  • Environment /Pollution related Norms: Also to be complied with such as allowable emission rate of NOx, SOx
READ  What is A Vibration Analyzer? Applications and Working of Vibration Analyzers

Internal and External Coordination in Piping design

As the work of piping design tends to overlap with that of Process, Mechanical, Civil/Architecture, Electrical, Instrument engineering teams, and others, it is important for a piping engineer to work in close coordination with related departments all the while maintaining a broad and comprehensive view of the plant.

  • The process is the upstream discipline for the engineering group. The process provides PFD, Process Data Sheets, P&ID, Equipment List, Line List, etc.
  • The mechanical group gives us the Mechanical Data Sheet of Equipment. In the later stages of design, Vendor Prints (VPs) are made available.
  • The Civil/ Structural/ Architectural group provides the required foundation for equipment, structures for racks/ equipment, underground trenches, pits, structures for Miscellaneous Pipe Supports, etc.
  • The instrumentation group supplies the data for inline and online instruments, control valves, and relief valves.
  • Electrical gives the hazardous area classification drawings, cable layout, etc.
  • All these disciplines are also involved in preparing the Plot Plans
  • The piping design has enormous implications for plant construction, operation, and function.
  • Construction and Procurement may be an internal/ external group depending on the project scope
  • The most important external group to be coordinated with is the Client.
  • There are other external groups such as the Licensor and the PMC. They are equally important. ITB to be thoroughly read to understand the PMC requirement and the Licensor requirement.
Piping Vs Other Disciplines
Fig. 2: Piping Vs Other Disciplines

Anup Kumar Dey

I am a Mechanical Engineer turned into a Piping Engineer. Currently, I work in a reputed MNC as a Senior Piping Stress Engineer. I am very much passionate about blogging and always tried to do unique things. This website is my first venture into the world of blogging with the aim of connecting with other piping engineers around the world.

2 thoughts on “Outline of Piping Design: Basic Elements

  1. Hi brother, I am hemanth Bhagyanath. I am a mechanical engineer. I have always been interested in piping engineering, but I had a career change to project management after 2 yrs I started my career. Now I feel I made a bad decision as it was not my thing. However now I had lost my job due to the covid. I just would like to know your opinion about switching to piping. How do you feel the scope currently for piping. I am interested in piping stress analysis , I wanted to learn and undergo trainings for piping. What may help me get in to a job ?
    Thank you for your time

  2. Project engineering is better. If you work as a piping engineer you will work with softwares and after sometime you will realise that your engineering ability is reduced to a cad operator. Then you cannot change your line.vsame thing with stress analysis- you are only a software operator without knowledge of Theoritical analysis
    By attending tere weeks of software training one cannot be a good engineer, he will be only a glorified draftsman, but working on a computer.
    Many gradutesoptings to work with softwares are stuck and can not det promotion as a engineer.

Leave a Reply to Laxminarayana Pai Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts