Piping Reducers: Concentric Reducers, Eccentric Reducers

A piping reducer is a type of pipe fitting that reduces the nominal bore from a bigger inner diameter to a smaller inner diameter. Piping and Pipeline Systems are not of uniform size and there is a requirement of reducing or expanding the lines depending on process requirement or availability of material. Here comes the importance of a special pipe fitting called Reducers.

Piping Reducers are one of the most extensively used fittings in the piping industry to reduce or expand the size of the straight part of the run pipe. Basically, reducers are available in two styles:

  • Concentric reducers and
  • Eccentric reducers.

Concentric Reducers

As shown in Fig. 1, In concentric reducers the area reduction is concentric and the centerline of the pipe on a bigger end and smaller end remains the same.  These styles are normally used for vertical lines. So in concentric reducers, the pipe axis remains the same. Reducers are reversible and can be used in any direction.

Concentric Reducers
Fig.1: Concentric Reducers

Eccentric Reducers

As shown in Fig. 2, in eccentric reducer there is an offset in between the center lines of the bigger end and the centerline of smaller end. This offset or eccentricity will maintain a flat side either on top or on the bottom side.

Eccentric Reducer
Fig.2: Eccentric Reducer

This offset or eccentricity can easily be found out by the following equation:

Eccentricity=(Bigger end ID-Smaller end ID)/2

Eccentric Reducer Installation

While using eccentric reducer, the user has the option of orienting the flat side. Usually, for horizontal lines, eccentric reducers are oriented with either the flat side up or down, and the same with deviation is mentioned in isometric.

Normally eccentric reducers with the flat side down are preferred for following cases on horizontal lines:

  • On Sleepers and Piperacks
  • On lines requiring gravity flow
  • On the pump suction line which handles slurry.

Eccentric reducers with the flat side up are used for all pump suction lines (excluding pumps handling slurry) on horizontal lines. This way one can avoid air getting trapped inside the pipeline during initial venting through pump casing and will help in avoiding Cavitation.

Types of Piping Reducers based on End Connection

Depending on end connections of this fitting with a straight pipe, reducers are grouped as follows:

Butt-welded piping reducers

The applicable pressure rating, dimensional and material standards for butt welding reducers are the same as those applicable to butt welding elbows.

Socket welded piping reducers

As shown in Fig.3. such reducers are available in concentric type only &  in the form of coupling with one end socket to fit larger diameter pipe and another end socket to fit smaller diameter pipe.  Standards are the same as those applicable to socket welding elbows.

Socket Welded Reducers
Fig.3: Socket Welded Reducers

Screwed piping reducers

Available only in the concentric type and are in the form of coupling having one end to fit bigger pipe and another end to fit smaller pipe.  ASME B16.11 is an applicable dimensional standard. Material standards including pressure ratings are the same as of screwed elbows.

Flanged and Screwed Reducer
Fig. 4: Flanged and Screwed Reducer

Flanged piping reducers

Their pressure rating, use, material, and dimensional standards are the same as those applicable to flanged elbows. Regardless of reduction, their face to face dimensions is governed by the larger pipe size.

Piping Reducer Fitting Dimension

The dimensions for butt welded piping reducers are provided by ASME B 16.9. In pipe Data Pro software, you can easily get the required pipe reducers dimensions. The following image provides part of the pipe reducer size chart as a reference.

Pipe Reducer Dimensions
Fig. 5: Pipe Reducer Dimensions

Few more related resources for you.

Piping Elbows vs Bends: A useful literature for piping engineersOpens in a new tab.
“Pipe Coupling”-A short Introduction for the piping professionalsOpens in a new tab.
Different Types of Hose CouplingsOpens in a new tab.
A Literature on Piping Nipples for piping and plumbing industryOpens in a new tab.

Print Friendly, PDF & Email

Anup Kumar Dey

I am a Mechanical Engineer turned into a Piping Engineer. Currently, I work in a reputed MNC as a Senior Piping Stress Engineer. I am very much passionate about blogging and always tried to do unique things. This website is my first venture into the world of blogging with the aim of connecting with other piping engineers around the world.

3 thoughts on “Piping Reducers: Concentric Reducers, Eccentric Reducers

  1. Thanks for the very good article.

    I wanted to know about the basic difference between Swage nipple and Reducers.

  2. Thanks for the article

    In addition, it must say that standard ASME B16.9 used for butt welding reducers and B16.11 for forged steel, socket welding and threaded ones.
    In selection of the materials, reducers and other components must made of material having at least the similar allowance stress of the pipe and must have a pressure retention strength of at least 87.5% of the wall thickness of the matching piping.

    Cheers

  3. Furthermore, when the reducer size dropped less that 2″, it will be called Swage nipple and it is covered by MSS SP 95. connections are socket welding and threaded.

Leave a Reply to Somnath Cancel reply

Your email address will not be published. Required fields are marked *

Recent Content

Enable Notifications    Ok No thanks