AIV – What Is Piping: All about Piping Engineering

What is Acoustic-Induced Vibration or AIV? Acoustic-Induced Vibration or AIV is a severe high-frequency vibration that the piping systems carrying vapor or gases may experience near the high pressure reducing devices. Due to high-pressure drops of vapor/gas services in this pressure-reducing device like a relief valve, orifice plate, control valve, depressuring valves, Choke Valve, Blow Down valve, etc a high-frequency sound wave in the range of 500–2,000 Hz is generated. This wave energy induces vibration (and stress) and excites the pipe wall in the circumferential direction causing radial pipe displacement and eventually acoustic fatigue failure within a very short period of time (Few minutes or hours). Piping components with high-stress concentration zones like pipe fittings, small-bore connections, Fabricated tee, welded pipe supports, etc are prone to such acoustic induced vibration failures. Since the high viscosity of liquid or two-phase fluid dampens the circumferential pipe displacements, Acoustic Induced Vibration or AIV is not a concern for such systems. Cause of Acoustic Induced Vibration There are two main causes for Acoustic Induced Vibration (AIV), they are: high-pressure drops and high flow rates in vapor/gas services Mechanism of Acoustic Induced Vibration (AIV) In Acoustic Induced Vibration, the high-velocity fluid impingement on the piping wall, turbulent mixing, and shockwaves downstream of the flow restriction gives rise to a high level of noise. This noise level is a function of pressure drop across the pressure reducing device and gas/vapor mass flow rate. The noise is transmitted downstream of the flow restriction losing energy to friction, work is done by vibrating the pipe, and heat lost to surroundings. A noise or sound level of 155 dB is considered a safe level when the circumferential vibration is no longer a concern. Industry standards and experience show acoustic energy attenuates 3 dB for every 50D of piping from the source. The response caused by high-frequency acoustic excitation affects the piping downstream of the source to the first major vessel, i.e, Separator, KO drum, etc. Screening for Acoustic Induced Vibration Design Engineering Practice (DEP) by Shell Global Inc provides rules for screening the systems for Acoustic Induced Vibrations (AIV). To study the effect of AIV on the piping system it is required to calculate sound power level at the concerned pressure-reducing device based on the following equation: Sound Power Level Calculation Where: P1 is upstream pressure (bara) P2 is downstream pressure (bara) W is flow rate (kg/s) T is the upstream temperature (K) Mw is molecular weight (grams/mol) SFF is a correction factor to account for multiple occurrences of sonic flow in a line. If consecutive sonic conditions exist, then SFF=6; otherwise SFF = 0. All the above-mentioned data can be received from the Process engineering team. If the calculated Sound power level is less than (or equal to) 155 dB, then there is no concern from AIV viewpoint. However, if the calculated Sound power Level is more than 155 dB, then the LOF (Likelihood Of Failure) value needs to be calculated following steps provided by Energy Institute guidelines for the avoidance of vibration induced fatigue failure in process pipework. Mitigation of AIV Considerations for Acoustic Induced Vibration mitigation must be done during the design stage of the project as failures in AIV can happen within minutes of operation. There are various options for AIV mitigation. However, the following options are the most common: Using a higher pipe schedule or lowering the D/t ratio.Decreasing flow velocity by increasing pipe diameter.Using smoother pipe fittings which ensures a smooth transition from branch to the main header.Using Clamp-on supports and stiffening rings.Using a full wrap-around pad on welded pipe supports. Full wrap-around is more commonly accepted in industry standards than partial reinforcing.Using Multi-Stage Pressure Drop Internal Trim (Low noise trim) to reduce noise levels at the valve.Using In-line Acoustic Silencer downstream of a pressure reducing valve will reduce the acoustic energy near its origin point and prevent its further propagation. However, as silencers themselves are susceptible to mechanical damage from high acoustic energy exposure, this is not suggested.Increasing line length between acoustic induced vibration source and high-risk stress concentrated locations Attenuation of acoustic energy at the source is the most preferred approach to achieve acceptable sound power energy in a piping system if the same is physically and economically feasible. Two types of devices can accomplish this: Low Noise Control Valves: As the acoustic energy generated due to turbulent fluid stream are highly sensitive, valve manufacturers design valves to generate lower levels of acoustic energy, known as low noise control valves. Depending on the sound power energy attenuation requirement of the system various design options are available like:Multipath Design with special low noise trim.Staged Trim designLadyrinth Disk designRestriction Orifice: The acoustic energy generated at source can be controlled by multi-stage restriction orifice. One stage pressure let-down systems operate at choked flow conditions generating extremely high levels of acoustic energy. This causes increased turbulence and shock waves in the downstream. Installing a series of restriction orifices (multi-stage) downstream of the let-down valve will attenuate this acoustic energy. Using multiport expansion plates in restriction orifice design is also an alternate option for mitigating acoustic induced vibration. If reducing the generated acoustic energy is not feasible, finding options to reduce the level of resonant response can be considered. Steps must be considered to dampen the vibration amplitude or to improve the mechanical integrity of the piping system by reducing stress concentrations. System damping can be increased by using anti-vibration materials (elastomer). Stress concentrations can be reduced by increasing pipe thicknessesusing full-wrap reinforcementsusing standard branch connections (Welding Tee, Olets, etc) in place of un-reinforced fabricated connectionsRemoving screwed fittingseliminating branches 2 inch and smalleravoiding abrupt geometric changes in line. Comparison of FIV and AIV The following image shows the comparison between Flow Induced and Acoustic Induced Vibrations in a Piping System FIV and AIV Comparison Few more related Resources for you.What is Acoustic-Induced Vibration or AIV?What is Flow-Induced Vibration (FIV) in a Piping SystemBasics of Vibration Monitoring: A PresentationMotion Amplification Technology (MAT) for Piping Vibration VisualizationCommon Causes and Effects of Piping VibrationSolving vibration problems in a two-phase flowline by Dynaflow Research GroupConsiderable points while installing centrifugal pumps at the site to reduce vibration References and Further Study Energy Institute guidelines for the avoidance of vibration induced fatigue failure in process pipeworkhttps://www.bechtel.com/getattachment/Blog/technical/October-2019/Differentiating-Between-Acoustic-and-Flow-Induced/Differentiating-Between-Acoustic-and-Flow-Vibrations.pdf DEP 31.38.01.26 V43