cavitation of pump – What Is Piping

What is Pump Cavitation? Pump cavitation is a destructive issue that can generate excess noise and energy usage to serious pump damage. The problems of pump cavitation is not new and ever-growing. It seriously affects the pump operation and lifespan. However, the pump cavitation can be easily avoided with the right planning and troubleshooting. Cavitation is an important term for rotating equipment engineers. The generation of vapour bubbles or cavities in a fluid flow due to low pressure and its sudden collapse causing damages in the related parts like impeller, pump housing, etc are termed as Cavitation. It is one of the major problems for Centrifugal pumps. There are various criteria that can describe the occurrence of cavitation, extent and impact of it. Cavitation occurs when the liquid in a pump creates air bubbles because of the partial pressure drop of the flowing liquid. Insufficient net positive suction head available is the main cause of generating air bubbles. Changes in the liquid pressure in the pump turn the liquid into vapor. As the liquid moves by the pump’s impeller spinning, the air bubbles move, instantaneously implode. The collapse of vapor bubbles creates a shockwave that erodes the impeller surface. When a strong cavitation occurs at the impeller inlet, the pump performance decreases, leading to even pumping failure. Pump Cavitation is usually common with centrifugal pumps as these types of pumps work by changing pressure inside the unit to create a vacuum, pushing the liquid into the unit as opposed to pulling it in. Cavitation is submersible pumps are less frequent. What Causes Cavitation? When the suction pressure drops below a certain value, the performance of centrifugal pump deteriorates. This suction pressure that is often decided with respect to vapour pressure at suction temperature is called Net Positive Suction Head that is popular by its acronym NPSH. If this NPSH drops, impeller inlet pressure may fall below the vapour pressure which causes vapour bubbles or voids to generate. If the flowing liquid is then subjected to pressures above the vapour pressure, these voids can implode causing damage, which is called cavitation. The most well-known causes of cavitation are: Not meeting the required NPSHThe pump is installed at too high of a distance above the fluid sourceSuction pipe diameter is too smallPipe blockage on the suction sideClogged or obstructed filtersLength of the Suction pipe is more.Excessively high suction lift.Poor piping designFlowing liquid is having a very low vapour pressureFluid is overly heated to the point of vaporization.The pump is running too far right on the pump design curveThe Pump Speed is more Due to high-vacuum or low-pressure environment, the flow in the pump is not proper.High discharge pressure.Poorly specified pump. Cavitation and its Effect Cavitation Types Two types of cavitation are more prevalent in rotating equipment engineering; Vapor Cavitation and Gas Cavitation. Vapor Cavitation When the static pressure in a flowing fluid falls below the vapor pressure, Vapor cavitation develops. At the same time, the presence of nuclei or microscopically small vapour bubbles is required for the cavitation to form. The static pressure decreases if the local velocity is increased or the inlet conditions change. Now, the generated vapor bubbles implode suddenly at a very high velocity, when the static pressure rises above the vapour pressure in the flow direction. This sudden implosion may lead to material erosion, a rise in noise levels, rough running of the pump and a drop in pump efficiency and head. Normally, as the implosion begins, vapour bubbles will dent inwards and later a water microjet is formed that is directed at the wall and strikes with a high velocity. This sequence of all events, along with with the fissured microstructure, very fine pores, indentations and cracks in the wall surface is the main reason behind the material’s destruction, which is accelerated in the presence of mechanical stress. Gas Cavitation When the bubbles are generated due to release of dissolved gases from solution in conjunction with diffusion, Gas Cavitation occurs. When the fluid's pressure drops below the saturated vapour pressure, Dissolved Gases come out from the solution. This mechanism is dependent on the concentration of the dissolved gases. In terms of material damage, Gas cavitation is not as destructive as vapour cavitation, because, with rising pressure, the gas diffuses into the liquid again which means that this process is much slower than the collapse of vapour bubbles. Bubble Formation During Cavitation The formation of Vapour and Gas may overlap, as well. Vapour bubbles which are generated when the fluid’s pressure reaches or drops below vapour pressure may also contain gas which can release from the solution via diffusion while the fluid approaching the suction of the pump. So both of these two cavitations together, intensify the extent of the impact on the fluid flow. Depending on the location of pump cavitation on suction or discharge side, pump cavitation can also be grouped as Suction cavitation and discharge cavitation. Symptoms/ Effects of Cavitation As a result of cavitation, One or a combination of the following symptoms or effects can be generated: Unexpected VibrationsPump performance deterioration. Decreased or Reduced Flow or PressureErosion of the ImpellerSeal and Bearing Failure Erratic Power ConsumptionDistinct Noise.Mechanical damage. How to Prevent Cavitation? An obvious way to guarantee that there will be no pump cavitation is to restrict the void or bubble generation. This can be done in various ways like Lowering the pump speed.Raise the liquid level to increase the NPSH so that lower pressure scenario does not occur.Lowering the operating temperature.Reduction of Pump motor RPM. Running the pump at the ideal rpm.Using a booster pump to feed the principal pump.Increasing the impeller diameter.To properly operate a pump best suited for the applicationSelecting the impeller inlet geometry that ensures no vapour formation.Using two lower capacity pumps in parallel.Installation of an impeller inducerStrictly following the pump’s manufacturer performance guidelines.Increasing pump suction line size.Altitude or height has a major effect on the pump cavitation. At higher higher altitudes, special care must be taken to make sure that cavitation does not occur since liquids boil at a much lower temperature.The fluid temperature need to be monitored to keep cavitation under control.Avoiding pockets for air or vapor accumulation.Keeping pipe reducers as close to the pump as possible.Regular pump maintenance.Installing the pump at proper location Few more resources for you.. MAJOR FACTORS AFFECTING THE PUMP PERFORMANCE”: A short article NPSH for Pumps: Explanation and Effect Water Hammer Basics in Pumps for beginners Pumps & Pumping Systems: A basic presentation A brief presentation on “CENTRIFUGAL PUMP WITH SPEED CONTROL” Stress Analysis of Pump Piping (Centrifugal) System using Caesar II Considerable points while Commissioning and starting-up a Process Pump Considerable points while installing centrifugal pumps at site to reduce vibration Reference and further Studies KSB Knowledge Bank. https://oaktrust.library.tamu.edu/handle/1969.1/164365 https://www.globalpumps.com.au/blog/what-is-pump-cavitation-and-how-to-prevent-it