Elavated Flare – What Is Piping: All about Piping Engineering

What is an Elevated Flare System? The elevated flare system consists of a flare header, knock out drum and a flare stack. The waste gas and condensate are collected from the whole plant through the flare header and then the condensate is separated in the knock out drum and finally, the gas is burnt in a stack at high elevation. As the combustion of gases (toxic) is done at flare tip at high elevation, the complete system is called Elevated Flare System. Purpose of flare system The primary function of a flare is to use combustion to convert flammable, toxic, or corrosive vapors to less objectionable compounds like CO2. Why not cold vent instead of flaring? Methane is roughly 30 times more potent as a heat-trapping gas than CO2. Hence cold venting of HC gases is not allowed as per pollution control board directives. Design standards for Flare System API 521: Pressure-relieving and Depressuring systemsDEP 80.45.10.10: Flare and vent systems (amendments to API 521)API537: Flare details for refinery and petrochemical serviceDEP 80.45.11.12: Flare details (amendments to API 537) Types of Flares (Fig. 1) Elevated flares: Commonly used in the oil and gas industry and the most economical.Enclosed flares: Used in plants where a visible flame is not acceptable. Also used for offshore facilities.Advantage: Low noise and radiation levels; Disadvantage: Poor dispersion of gases during flameout condition (flare needs to be tripped on gas detection)Ground flares: Used for liquid or two-phase relief flaring. Advantages: Low radiation, low noise; Disadvantage: accumulation of vapor cloud, high initial cost. Fig. 1: Types of Flares Types of Elevated Flares (Fig. 2): Self-supported stacks Simplest and most economical design; Stack height up to 100 ft overall height; As the flare height and/or wind loading increases, the diameter and wall thickness required to become very large and expensive. Guy wire supported stacks Most economical design in the 100- to 350-ft height range. Normally, sets of 3 wires are anchored 120 degrees apart at various elevations. Derrick supported stacks The most feasible design for stack heights above 350 ft. Derrick supports can be fabricated from pipe (most common), angle iron, solid rods, or a combination of these materials. They sometimes are chosen over guy-wire-supported stacks when a limited footprint is desired. Fig. 2: Types of Elevated Flares Non-Assisted / Assisted Flares: Non-assisted flares are the flares that do not use any assist media and typically used for hydrocarbon or vapor streams that do not cause smoking (i.e. For clean-burning gases like methane, hydrogen, carbon monoxide, ammonia, hydrogen sulfide) or when smoke is not a consideration.Incomplete combustion of heavy HC gases produces Carbon monoxide, which is the main component to create smoke. For flaring heavy gases, a smokeless operation can be achieved by assist media such as steam, air or gas which improves the mixing of flare gas with air.Steam assisted flares (Fig. 3) for smokeless operation. Steam increases momentum of flare gas which enhances fuel-air mixing leading to complete combustion. Also, water-gas shift reaction converts CO to CO2 CO + H2O ⇌ CO2 + H2 Air-assisted flares (Fig. 3) are used where smokeless burning is required. It is used when steam is not available or where low-pressure air delivery offers a lower cost. (the only fraction of requirement of air is mixed with flare gas to promote momentum which effectively entrains additional combustion air from surrounding). Fig. 3: Steam Assisted and Air Assisted Flares Flare load estimation (Fig. 4) Fig. 4: Example of Flare Load Estimation Fire zone: Wetted areas within a 300 m2 (3200 ft2) plot area shall be considered when a system's relief loads are calculated.Flare gas flow rate: Tip diameter is decided based on design flowrate.Mach number in Stack: 0.5Mach number in tip: 0.5 to 0.8 (depends on allowable pressure drop)Lower gas velocity (Fig. 5): When the gas flow is so low that the local gas velocity is less than flame velocity, air entrains into the flare tip leading to burning back / flashback. At very low gas velocities, the flame can travel back through the mixture (flashback) into piping and KOD. Fig. 5: Effect of Lower and Higher Gas Velocity Higher gas velocity (Fig. 5): When the gas flow is higher than design capacity, then the local gas velocity becomes higher than the flame velocity leading to detached flame or flameout (higher velocity leads to turbulence, which in turn reduces HC component concentration below LFL)Flame velocity: The burning velocity or flame speed is the velocity at which a flame front moves through the un-burnt gas/air mixture. This flame speed varies with the air/gas mixture ratio and the chemical make-up of the gas.Purge gas requirement: To avoid air ingress down the flare stack purge gas is injected in flare header. The injection rate should be controlled by a fixed orifice, rotameter or other devices that ensure the supply remains constant and is not subject to instrument malfunction or maladjustment. Purge reduction seals (Fig. 6): To reduce the purge rate purge reduction seals are used. Liquid seal The liquid seal drum shall be designed as a pressure vessel with a design pressure of at least 7 barg (100 psig) to maintain containment against an internal deflagration. Where there is a risk of an obstruction in the flare due to process flows creating an ice plug with the liquid seal, alternate sealing fluids such as a glycol/water mixture (60% EG & H2O freezing point –45 deg C) or other means to prevent freezing SHALL [PS] be implemented. For LNG facilities, liquid seal drums shall not be used, since in the event of a cold release this may form an obstruction in the flare relief system. Allowable Liquid droplet size (to avoid burning rain): Burning rain occurs when rate of burning (depends on type of flare) of liquid droplets is lower than rate of settling of droplet (depends on droplet size). Fig. 6: Purge Reduction Seals Drift distances of burning liquid droplets from an inadequately designed flare system can be considerably greater than 200 ft (60 m). If the liquid is not drained from flare gas, at a gas velocity of 3-4 m/s - liquid droplets of 1000 micron can be entrained which can cause burning rain in the flare. Liquid droplet size allowed without burning rain Unassisted flares: <600 micrometerSteam or air-assisted: <600 micrometers (less than 1% mass)High pressure (if operated at at least 200 kPag) : <1000 micrometer (less than 1% mass) Flare Knock Out Drum (KOD) Design pressure of KOD: 5 barg (50 psig) when a liquid seal drum is located between the KO drum and flare stack.7 barg (100 psig), if there is no liquid seal drum in the system. For a multi-process unit facility (e.g., refinery) based flare KO drum where it may not be immediately clear which unit is sending liquid to the flare, liquid space on top of LA (HH) SHALL [PS] be designed to contain the maximum emergency liquid relief rate from the largest single contingency for a period of at least 15 minutes for the unit KO drum and at least 20 minutes for the flare KO drum, without taking credit for pump out capacity. Flare Height The height of the flare (Fig. 7) is established based on allowable thermal radiation levels. Flare height depends on the available plot, the distance of nearby equipment from the flare stack. More plot area: Low flare stack heightLess plot area: Higher flare stack height Fig. 7: Flare Height vs Available Plot Area Thermal radiation: Effect of thermal radiation on a person at grade or at elevated platform shall be checked by radiation calculation. Thermal Radiation affects human skin (skin burn). Exposure Times Necessary to Reach the Pain Threshold 31 kW/m2 – Up to 20 s15 kW/m2 – Up to 1 hour58 kW/m2 - Continuous If personnel exposure to radiant heat exceeds the guidelines provided, then shielding should be considered. Depending on the location the thermal radiation limit is provided in Fig. 8 The solar radiation need not be added to calculated thermal radiation values (0.79 to 1.04 kW/m2) from the Flare. For OXY projects, solar radiation to be considered.A wind velocity of 10 m/s (22 mph) at the elevation of the flare tip, blowing towards the receiver, is a typical assumption for flame tilt assessment.When two flares are located in close vicinity, combined radiation effects shall be calculated. Fig. 8: Thermal Radiation Limit Dispersion Analysis To ensure safe operation during periods when the flame might have extinguished, the concentration of hazardous components should be determined using dispersion analyses, assuming the flare is functioning as a vent only. Level of ConcernHydrogen Sulphide(Concentration, Time)Sulphur Dioxide(Concentration, Time)8 Hour TWA (Threshold Limit Value)5 ppm, 8 hours2 ppm, 8 hours15 Minute STEL (Short Term Exposure Limit)10 ppm, 15 minutes5 ppm, 15 minutes Short-term exposure limits (STELs) are set to help prevent effects, such as eye irritation, which may occur following exposure for a few minutes Smokeless requirement Local rules and regulations shall be followed. Typically flare combustion quality shall meet Ringelmann Index 1 criteria (Fig. 9). Smokeless flowrate shall be the normal flow which is expected in day to day operations. Do not specify the design capacity for smokeless operation. A scale used to define levels of white, gray and black i.e. intensity of smoke Ringelmann No. 0 is clear smokeRingelmann No. 5 is 100 percent black.Ringelmann No. 1 is equivalent to 20 percent black Fig. 9: Ringleman chart Other requirements Noise: For normal flowrate (including starting-up and shutting-down): 85 dB(A) at the sterile radius. For emergency conditions: 115 dB(A) at sterile radiusCombustion efficiency: greater than 98%Number of pilots (Fig. 10): The number of pilots required is a function of the flare burner diameter. For very small flares, a single pilot will reliably light the flare gas. However, it should be noted that if only a single pilot is used, a single pilot failure would represent a complete failure of the ignition system. Recommended installing at least 2 pilots for tip size of up to 8" to increase reliability. As the flare burner diameter increases, the number of pilots required to reliably light the flare, regardless of wind direction, increases. Fig. 10: Number of Pilots Flare gas recovery system Safety considerations Path to flare: PRVs, depressuring systems, etc., shall always have flow paths to the flare available at all times.Reverse flow: Because flare gas recovery systems usually involve compressors that take their suction directly from the flare header, the potential for reverse flow of air from the flare into the compressors at low flare gas loads shall be considered.Monitor oxygen content in the flare header and provide recovery system trips. Provide a low-pressure trip on the recovery system suction to avoid air ingress. Liquid seal drum (not practical in AP flare systems) Few more useful Resources for you… Pre-Commissioning and Commissioning Checklist for Flare Package Routing Of Flare And Relief Valve Piping: An article-Part 1 Flare systems: Major thrust points for stress analysis Stress Analysis of PSV connected Piping Systems Using Caesar II Articles related to Process Design Piping Layout and Design Basics Piping Stress Analysis Basics Few Job Opportunities for you