Hydro-Cyclones – What Is Piping: All about Piping Engineering

Produced Water Source Hydro Carbon reservoirs always have water along with crude/gas. The water(brine) brought to the surface from the hydrocarbon-bearing reservoirs during the extraction of oil and gas can include formation water, injection water, and any chemicals added downhole or during oil/water separation processes is termed “Produced Water”. The produced water is very high in salt content and also contains oil in dispersed form and therefore needs to be treated before it is disposed of. This article will mostly concentrate on the Conventional Methods for Oil Removal from Produced Water. Contaminants in Produced Water Fig. 1: Contaminants in Produced water Produced Water Disposal The major disposal / re-use of Produced Water are Re-Injection for Pressure MaintenanceInjection in Disposal wellsOverboard Discharge Every disposal mechanism has quality criteria, and the same shall be met before disposal. The typical disposal criteria are as given below: CriteriaWater InjectionInjection in Disposal WellsOverboard DischargeOiW (ppm)~10 ppm10-40 ppm40 ppm-100 ppm#Table: Typical Disposal Values for Produced Water Produced Water Cycle A typical produced water cycle is shown in Fig. 2 Fig. 2: Produced Water Cycle Classification of Produced Water Treatment Process Refer to Fig. 3 that explains the classification of Produced Water. Fig. 3: Treatment Processes Produced water Treatment Processes Produced water Treatment using SKIM TANK (Fig. 4): Principle: Gravity SeparationDescription and Operation:Designed to provide long residence times.Their design can include a simple tank with water inlet/outlet baffles and oil skimmer.In some designs, the well fluid first flows into a degassing chamber. Liquids flow down into the tank, and exit under a cone or spreader.In some designs, the oil and water compartments are separated within the tank and the skimming is ensured by Interface control. Fig. 4: Typical sketch of Skim Tank and coalescers Advantage and Disadvantage of Produced Water Treatment using Skim tank: Provide large surge capacity ensuring stable flow to downstreamLarge residence time also ensures solids separationRequire Large Footprint areaProduced water channeling (short-circuiting) recirculation or stagnant areas of fluid can occur due to poor internals design or build-up of solids. Produced water Treatment in COALESCER (Fig. 4): Principle: Coalescing and Gravity SeparationDescription and Operation:Coalescer includes installation of Coalescer Plates or Packs in the conventional separatorThe pack provides more surface for suspended oil droplets to coalesce into larger globules.In the separation process, the oil droplet size is very significant, therefore it is also installed upstream of separation devices to increase the Oil particle Sizes and thereby the efficiency of the downstream equipment. Advantages and Disadvantages of Produced Water treatment in Coalescer: No moving parts and simple controlLittle maintenance or attention requiredCan handle high levels of oil in the produced waterCapable of handling relatively large oil content fluctuationsPlates can block with solids or fouling hydrocarbons. Produced Water Treatment in API SEPARATOR (Fig. 5): Principle: Gravity SeparationDescription and Operation:Fluid Enters at one end and separates along the length as per density.Most of the suspended solids will settle to the bottom of the separator as a sediment layer, the oil will rise to the top of the separator, and the wastewater will be the middle layer between the oil on top and the solids on the bottom.Typically, the oil layer is skimmed off and re-processed or disposed of.The bottom sediment layer is removed by a chain and flight scraper (or similar device) and a sludge pump.The water separated is sent for further processing. Advantages and Disadvantages of Produced water Treatment in API Separator: Simple in designLarge residence time also ensures solids separationIs a very old design and has been replaced by CPI separatorSolids removal from the bottom is difficult and separated solids affect the separator efficiencyLarge footprint areaAtmospheric Design-Cannot be used for PWRINeed a degasser to be installed upstream Using CORRUGATED PLATE INTERCEPTOR (CPI-Fig. 5) for Produced Water Treatment: Principle: Gravity SeparationDescription and Operation:Fluid Enters at one end and separates along the length as per density just like an API SeparatorCPI includes corrugated plates arranged in a plate pack which installed at an angle of 45°The plate provides more surface for suspended oil droplets to coalesce into larger globules.Separated solids would slide down and separated oil drops move upwards due to its lesser density than water. Fig. 5: Typical Sketch of API Separator and Corrugated Plate Interceptor Advantage and Disadvantages of Corrugated Plate Interceptor in Produce Water Treatment: Corrugated plates enhance the degree of oil-water separation and therefore it requires significantly less space than a conventional API separatorAtmospheric Design-Cannot be used for PWRINeed a degasser to be installed upstream Produced Water Treatment in HYDRO-CYCLONES (Fig. 6): Principle: Centrifugal ForceDescription and Operation:Fluids enter the hydro-cyclone through the tangential inlet at the top which causes the fluids to spin and attain High Centrifugal forcesThe centrifugal forces in a hydro-cyclone are of the order of several hundred times normal gravity force. This promotes rapid separation.The clean water exits the Hydro-cyclone through the open end of the Tube at bottomA vortex finder in the outlet port reverses the direction of the hydrocarbon core and it is discharged under differential pressure control, from the reject port at the center of the Inlet EndIn order to maintain hydro-cyclone separation efficiency, the Pressure Differential Ratio (PDR) must be maintained within certain limits. The PDR is defined as follows: PDR=DPir/Dpio Where, DPir = Pressure at the inlet – Pressure at reject outlet; DPio = Pressure at the inlet – Pressure at water outlet; Oil removal efficiency will decline <1.5=1.7-2.0=<Volume of liquid routed to the reject increases Advantage and Disadvantages of Produced water Treatment in Hydro-Cyclones: Compact in designHigh Efficiency @ particle size less than 10micronsModular Design gives flexibility for capacity enhancementEnergy Requirement to pressurize Inlet is highHigh cost due to the Metallurgy-Erosion Issues Using Induced Gas Floatation(IGF-Fig. 6) for Produced water Treatment Principle: Froth FloatationDescription and Operation:IGF units operate by generating small gas bubbles and releasing these in the lower section of a vessel through which the water is flowing.These bubbles attach themselves to the dispersed hydrocarbon droplets, reducing their density and floating them to the liquid surface.The separated hydrocarbon is then removed and the treated water exits the vessel under level control.There are two methods of Inducing bubbles viz. Mechanical and HydraulicThe Mechanical method generated gas bubbles by means of motor-driven diffusers/impellers.The unwanted side effect of the shear forces required to generate the micron-sized gas bubbles was a reduction in the size of the oil droplets which adverse effect on the overall efficiency of these units.The Hydraulic method uses a stream of clean water from the outlet and mixes it with the gas from the vessel top in an eductor. The mixed stream is then injected in the floatation cells through nozzles.Hydraulically inducing the bubbles is results in lower shear forces in the flotation cell Advantage and Disadvantage of Induced Gas Floatation for Produced Water Treatment: Low CapexHigh Inlet concentration can be acceptableRelatively insensitive to changes in oil droplet sizeRequire steady flow for the effective operationNormally requires de-oiling chemical to be dosed upstream to optimize performance –High OPEX Fig. 6: Hydro-Cyclones and Induced Gas Floatation Produced Water treatment by Dissolved Gas Floatation(DGF-Fig. 7): Principle: Froth FloatationDescription and Operation:Bubbles are generated by saturating a liquid stream with gas, typically at a pressure of 44 to 87 psig (3 to 6 barg).As the liquid enters the Flotation Chamber it is depressurized and the gas is released as fine bubbles.The rising bubbles attach themselves to hydrocarbon and float them to the water surface from where they can be removed by a skimmer and weir arrangement.The main advantage of DGF is that the method of producing bubbles is relatively gentle. The absence of the High Shear Forces helps in better separation. Advantage and Disadvantages of Produced Water Treatment by DGF: Proven technologyMoving parts and associated maintenance requirementsDe-oiling chemicals normally dosed upstream to optimize performanceGas solubility decreases with increasing temperature which can make the technology less effective at higher operating temperatures Compact Floatation Unit (Fig. 7): Principle: Froth Floatation and Cyclonic EffectDescription and Operation:The CFU combines the swirling tangential flow effect of a hydro-cyclone within a gas flotation unit.The inlet fluid enters the vessel via one or more tangential inlets, establishing a mild rotation of the liquid in the vessel.Nitrogen or fuel gas is introduced into the vessel via a bottom distribution nozzle or “sparger” (there are some differences between vendors regarding how the gas is introduced into the vessel).The oil rejects from the vessel is normally removed via a central weir pipe at the top of the vessel. Advantage and Disadvantage: The residence times in CFU’s are significantly lower than traditional IGF systems, with residence times of 1 minute being typical, compared to 4 minutes for IGF systems.Significantly smaller and lighter than conventional IGFExcellent turndownNormally requires a deoiling chemical to be dosed upstream to optimize performanceSensitive to vessel motion Produced Water Treatment using Crushed Nut Filter (Fig. 7): Principle: Hydrophillic Nature of Crushed Nut Shells Description and Operation: Nutshell filtration involves the removal of suspended hydrocarbon liquids and solid matter from wastewater by passing the water through a bed of crushed nutshells(Typical-Walnut)The crushed nut shells have an affinity to hold the oil particles and the suspended particles.As the impurities are absorbed the media gets choked resulting in a higher pressure drop.This is an indication that the filter needs to be taken for backwashOnce backwashed, it is again ready for filtration. To keep the process un-interrupted the filters are with N+1 configuration to take care of the capacity reduction during backwash. Advantage and Disadvantage of Produced Water Treatment using Crushed Nut Filter: High quality water effluentVery efficient for IWRemoves TSS in addition to OiWThe backwash mechanism is high on Energy and MaintenanceErosional issues due to abrasive nature of mediaLarge and heavy equipment's Fig. 7: DGF, Compact Floatation Unit and Crushed Nut Filter Use of Dual Media Filter (Fig. 8) for Produced Water Treatment: Description and Operation: In a multimedia filter, two or more media with different grain size and density are used.Within each layer, there will be size segregation with larger particles at the top and smaller at the bottom.The advantage is that this helps to minimize blockage and also maximum bed depth utilization.As the impurities are absorbed the media gets choked resulting in a higher pressure drop.This is an indication that the filter needs to be taken for backwashOnce backwashed, it is again ready for filtration. To keep the process un-interrupted the filters are with N+1 configuration to take care of the capacity reduction during backwash. Advantage and Disadvantage: High-quality water effluentVery efficient for IWRemoves TSS in addition to OiWThe backwash mechanism is high on Energy and MaintenanceErosional issues due to the abrasive nature of mediaLarge and heavy equipment's Produced Water Treatment Future Development MEMBRANE FILTERSCENTRIFUGECARTRIDGE FILTERSVENDOR SPECIFIC DESIGN Fig. 8: Dual Media Filter