Vertical Reboiler – What Is Piping

Significance of Vertical Reboiler Vertical Reboilers play a significant role in the Process industry. Reboilers are a type of Heat exchangers which are used for heating the bottom fluid of industrial Distillation columns. Normally heat from steam (or any other high-temperature fluid) is utilized to boil the liquid from the bottom of a Distillation Column. Normally this heating effect generates vapor which is then returned back to the Column at a higher elevation to drive the distillation separation. The piping arrangement between column and reboiler for this action is normally very stiff and require careful Analysis to keep the column and Reboiler nozzle loadings within an acceptable limit. The following article will provide the Stress analysis methodology of a vertical Reboiler connected piping system using software tool Caesar II, developed by Coade Inc. Applicable codes and standards for Reboiler Piping Stress Analysis ASME B 31.3-Process Piping, ASME Section VIII-Pressure Vessel design (Normally column and reboilers are manufactured based on these codes), WRC 107 and WRC 297Sometimes it is required to qualify the Nozzle loads by using WRC modules if actual nozzle loads exceed the vendor allowable received. Reboiler Piping Stress Analysis Inputs Before starting the modeling of reboiler and column in Caesar II please be ready with at least the following documents: Column general arrangement drawing Reboiler general arrangement drawing Process P&ID and Line list (Also known as line Designation Table or LDT) for the connected piping Piping Material Specification or PMS Equipment Nozzle allowable loads Piping Isometrics, if any Column and Reboiler allowable nozzle Loads (Should be taken from Equipment Vendor in case no standard Project-specific load is not available) Temperature Profile for Modeling the Rebolier and Column Column Temperature In the absence of project-specific guidelines, the Operating/ Design temperature of Column shall be considered the same as the average of operating / design temperature of the column outlet piping attached on each draw-off nozzle Reboiler temperature Reboiler uses the following information in the absence of project-specific guidelines: Tube side Inlet Temperature = bottom (outlet) Piping temperature of the tower. The temperature of the tube = average temperature between tube inlet and outlet piping. Tube side outlet temperature = temperature of the tower inlet piping. If the temperature of Column inlet piping (channel outlet) is not known, consider the reboiler tube outlet temperature as mentioned in vendor drawing or confirm from process engineer. Shell side temperature = average of the Shell inlet (Normally Steam) and outlet piping (Normally Condensate). Modeling of the Reboiler with an Expansion joint in Caesar II Initially model the reboiler as a rigid body following the below-mentioned steps. Refer attached drawing (Fig. 1) as reference: 1. Model nodes 10-20 and 20-30 with tube outlet temperature and pressure considering channel material, diameter, thickness, length and fluid density (Also include insulation thickness and density if any) from Rebolier General Arrangement (Henceforth called GA) drawing. 2. Model node 30-40, 40-50 and 60-70 with shell average temperature and shell design pressure considering shell material and dimensions as mentioned in reboiler GA. 3. Model element 30-70 with Channelside average temperature and design pressure taking tube material, shell diameter and thickness from GA drawing. 4. Model 70-80 and 80-90 with tube inlet temperature and pressure considering channel material, diameter, thickness, and length. Fig. 1: Reboiler piping schematic diagram for modeling in Caesar II 5. Model element 50-100 with shell-side properties and model the support restraint at node 100. Similarly model all other support elements as required from GA drawing (check 2 lugs, 3 lugs or 4 lugs supported system). 6. Now make the elements 10-20, 20-30, 70-80 as flexible (i.e, non rigid)7. Check the total operating weight of the reboiler from GA (if operating weight is not available to assume 70% of water-filled weight) and the weight already considered in elements mentioned in step no 6 (considering fluid and insulation; you can do it easily by clicking the single run button in caesar II). Provide the remaining balance weight in rigid element 30-70 (tube weight). Recheck once again by clicking the single run button to ensure the actual weight in the caesar model matches with the weight provided in GA. In case there is no expansion joint in shell, model element 30-70 with shellside average temperature. Rest all other parameters will remain the same. As you are planning for a reboiler piping I am sure you know the modeling of the column and attached piping. So I am not describing it. So model the column and attached piping to make a complete system as shown in the attached figure (Fig. 1). Supporting Arrangement for Vertical Reboiler Piping Reboilers may be supported by the column or by making an independent structure. In both of the cases, there is a possibility to support the reboiler lugs directly on the structure or there may be a requirement of spring hangers (bottom mounted). Sometimes Slot holes and PTFE/graphite sliding plates are required to reduce frictional effects. So this information needs to be informed to the equipment vendor. Location of the lugs to be fixed in such a manner with respect to nozzles, bellows and other accessories to avoid fouling, etc. If the reboiler is supported on spring supports (See attached figure Fig. 2) then following points need to be considered: Spring should be designed for cold load condition Cold/Hot Load Conditions should be same for all the springs Spring should be designed keeping in consideration the empty weight of reboiler in case of standby and steam out condition.Slotted Holes are not required on the lug of reboiler in case of spring support Fig. 2 : Supporting Arrangement of Vertical Reboiler Piping using Spring hangers Mirror polished SS plates/PTFE plates if required are to be provided by the vendor If the loads on nozzle are quite large because of the back force due to spring in WNC Case, the Lock Nut (Refer above figure) can be provided on spring to act as the limit stop. The required gap shall be input in Caesar as a gap on restraint applied at spring in (negative Y) Direction. Stress Engineer has to provide details of Lock Nut (See the figure attached below, Fig 3) and the loads on the nut in Spring Datasheet. Fig. 3: Locknut arrangement for Reboiler Piping Supporting Load cases for Reboiler Piping analysis Load cases are to be prepared based on operation possibility. So one must consult with the process engineer to know all the possible load cases. Normal possibilities are mentioned below: 1. Operating temperature load cases (W+P1+T1) 2. Design temperature load cases (W+P1+T2) 3. Steam out temperature load cases (W+P1+T3) 4. Upset Condition load cases (W+P1+T4): This condition may arise if the fluid is flowing in one part of the reboiler and no fluid is flowing through the other. Normally during start-up, these types of cases may appear. Sometimes it may happen that you have to first heat the reboiler shell before you can start the flow of process fluid through the tubes. Consultation must be done with the process engineer while creating all such load cases. 5. Sustained load cases (W+P1) 6. Prepare all occasional and expansion load cases as per normal project procedures. It is sometimes required that two or three reboilers of similar type are connected to the same column. In this case some reboiler may be in stand-by condition. So that situation is also required to be interpreted while making load cases. So additional load cases need to be added accordingly. Few Important Notes related to Re-boiler Piping Stress Analysis Reboiler column circuit being one of the most critical systems from a stress analysis point of view one should take extreme care while analyzing such systems. The following notes will help the stress engineer to take an engineering judgment: 1)All of the junctions between shell & nozzle can be considered as reinforced after confirming from the Mechanical Department 2)If nozzle loads exceed the allowable, loads should be forwarded to mechanical for further evaluation. Alternatively, the stress engineer has to perform WRC or FEA to qualify the nozzle loads. It is better to forward the WRC/FEA output results to Mechanical for their review. 3)Nozzle loads should be checked thoroughly with spring setting when the reboiler is standby during steam out. 4)Flange leakage evaluation should be performed as per client requirement and the rating of flanges should be changed if required, and the same information should be forwarded to the Mechanical and Process Team. 5)Initially, the Nozzle loads to be forwarded to mechanical as three times the project-specific pressure vessel loads in Caesar to take care of the upset conditions. 6) The requirement of Spring supports, PTFE/SS plates, Slot holes, Locknut arrangement, etc. is to be marked in Engineering drawing for incorporation to final vendor drawing. 7) Location of lug to be fixed in such a manner with respect to nozzles, bellows and other accessories to avoid fouling, etc. 8) Fouling of Reboiler Nozzle (Shell Outlet) with structure should be checked. Fig. 4: Typical reboiler piping systems Few more useful Resources for youReboiler for Distillation Column and System Type SelectionShell & Tube Heat Exchanger PipingModeling of Shell and Tube Heat Exchanger in Caesar II for Stress AnalysisStress Analysis BasicsPiping Design and Layout BasicsPiping Material Basics