Construction – Page 4 – What Is Piping

Two types of storage tank erection methodology have become widely accepted and popular. The first one is the Conventional Method of Tank Erection & the other is the Tank Jacking method. Both of these tank erection methods are accepted by the API 650 and constructor. The selection of tank erection method basically depends on the site location or workshop where we are making these tanks. There is a popular myth that API 650 guides us to adopt the tank erection methodology. But that is not true. API 650 only guides us in the design, fabrication, welding, hydro testing & inspection of storage tanks. Conventional Method of Tank Erection In the conventional methods, cranes are used for tank erection as a sheet by sheet method. At first, the bottom and annular plates are erected. Then the lower course shell is erected and finally, the upper course shell is erected. Refer to Fig. 1 which shows an example of a double-deck floating roof Tank erection by the conventional method. Suppose there are a total of 9 shells in a Tank so the tank erection sequence shall be 1st shell coarse, 2nd shell coarse, 3rd, and then in last 9th shell coarse. Fig. 1: Double deck floating roof tank erection by conventional method In the case of small diameter Tank, the tank is fabricated at the workshop and then brought it to site by a trailer for erection. But the handling should be proper to avoid buckling, bending, and any damage. Fig. 2: Tank erection by conventional method. In the case of Shop fabrication, the tank fabrication, erection, & assembly is done by EOT (electric overhead traveling) crane at the shop and then shifted to the site by a trailer. Fig. 3: Tank Fabrication at shop Fig. 4: Mobilizing fabricated tank to the construction site Tank Erection by Jacking Method Jacking method is the advanced form of tank erection. Jacking method uses the technology of Swedish Company Bygging Uddemann AB. A number of hydraulic Jacks are placed inside the tank to be erected. Refer to Fig. 5. In recent times this method is widely used in all developed countries. A system of hydraulic pressure hoses interconnects the hydraulic jacks which are energised by the action of a hydraulic pump. Fig. 5: Tank Erection by Jacking Method This method is just opposite of the conventional method. The construction sequence is just the reverse of conventional one. If there are total 9 shell course, the erection in jacking method will start from the 9th, then 8th, 7th and in last 1st shell course will be erected. The number of hydraulic jacks is decided based on the total weight of the roof & shell courses except for the bottom courses. Standard practice is to keep a 3000 mm distance between two jacks. However, the number of hydraulic jacks can be increased to meet additional wind load. Fig. 8 shows a typical jack used for tank erection. Tank Jacking Procedure The following steps are followed while erecting tanks by jacking procedure: Tank pad to be checked and tolerances to be verified.Since jacks are to be mounted on the annular plates, these need to be placed.Annular plate joints are to be aligned and welded.Next, erect the floor plates and align the joints to complete the welding of bottom seams.After that, Erect the top 2 courses. Align properly and weld. All the works on these two courses including the erection of the curb angle, wind girder for Floating Roof Tanks (or) roof structure and roof for Cone Roof Tanks, hand railing, etc to be completed.Next, Place the hydraulic jacks along the circumference of a circle drawn about 100 mm from the shell plate circle. The maximum arc distance between the two Jacks shall not exceed 3000 mm.Jacks are available in 8 T / 12T capacities. So arrange hydraulic jacks of predetermined quantities before starting the erection. Anchor the jack supporting columns to the base plate.When, the sub-assembly consisting of top 2 courses, roof structure/roof (or wind girder) railing, etc. is lifted, erect the shell plates of the third course from the top, after lifting the entire subassembly to the required height. Align the vertical joints and weld. Next, the sub-assembly is lowered to complete the alignment and welding of the girth seam. The hydraulic jacks can be released and lowered after the alignment of the girth seam,In a similar way, erect the other shell courses till all courses are erected.Finally, Align the shell to the bottom joint and check for the verticality of the completed tank. Weld the shell to the bottom joint.Now, all other balance works like fixing and welding of shell manholes, nozzles, etc. can be completed. Various terms are used while erecting tanks as mentioned below: Fig. 6: Stay Pipe and Power pack machine Power Pack Machine (Fig. 6): This Machine is used to lift the Jack. This machine Pumps the oil to Jack through the hose pipes to lift the jack.Stay Pipes (Fig. 6): Also known as supporting pipes; These pipes provide support to jack and trestle pipes. Basically these pipes are supporting the vertical trestles to maintain the verticality.Trestle Pipes (Fig. 7): These are the vertical members in the Jacking system that carries loads of Jacks. While installing this assembly we need to take extra care of these vertical members so that verticality of the Tank is maintained. Jacks Move over the Trestles by teeth. These get support from base plates in the Tank bottom. Fig. 7: Example of Trestles Difference between Conventional and Jacking Method The main differences between the conventional tank erection and jacking tank erection method are provided in a tabular format below: Fig. 8: Typical Jack for Jacking Method Conventional Tank Erection MethodTank Erection by Jacking MethodSuitable of all types of tanks with any diameter and heightLarge diameter tanks with higher plate thickness requiring double sided welding is not possible to erect by this method. Not fully feasible for double wall tanks.Very good dimensional control possible: Shell and bottom shapes obtained can be close to designed dimensions.Dimensional control comparatively less.Erection time is comparatively moreErection time is less.Safety issues as working at heightSafe erection as working at ground level. So lower risks.Resource requirement is more, hence more costlyEconomical erection.Possibility of wind damage while erection.Protective tank roof and wind girders eliminate the possibility of wind damage.Inspection Access is difficultEasily accessibleLower productivityBetter productivityHigh capacity cranes are requiredThe involvement of high capacity cranes is comparatively less.Difficult operation with less efficiencySmooth operation with high efficiencyConventional Method vs Jacking Method To summarize, the tank erection methodology by jacking method has many advantages over the conventional ones which include easy to operate, safe and reliable, accurate control of the weld gap and the height of lifting rod, good quality of the project, and provides an outstanding economic benefit. References and Further Studies: https://www.iqpc.com/media/8544/24895.pdfhttps://3.imimg.com/data3/TQ/MO/MY-3035455/tank-erection-jack.pdf Click here to refer a few more related resources