Importance of Gasket m and y Factors

In flange leakage analysis using ASME Section VIII method, you have come across two important factors for gaskets as input. They are gasket m factors and gasket y factors. In this article, we will learn about the importance of these two factors in piping stress analysis.

What is Gasket m Factor?

Gasket m factors are known as gasket factors. The value of m is dependent on the gasket material and construction. These gasket m factor values are used as a multiplier factor for determining the necessary compressive load on the gasket to maintain a seal when the pipe is pressurized. The gasket factor m is also known as the maintenance factor. m factor is dimensionless as the values of the gasket m factor are usually calculated as the ratio of the net pressure to the internal pressure. In Caesar II software, the gasket m factor is termed the leak pressure ratio.

This constant ensures that the flange has adequate strength and available bolt load to create good sealing without leakage. At the same time, the joint will withstand the effects of hydrostatic end force or internal pressure.

Importance of Gasket Factor m

The gasket factor m is used to calculate the required bolt load for a flanged joint to work properly during the operating condition. As per ASME BPVC Sec VIII, the required bolt load in operating condition is Wm1= H + Hp = 0.785G2P + (2b x 3.14GmP)

READ  High Temperature and High-Pressure Piping

What is Gasket y Factor?

The gasket y factor is the minimum gasket or joint‐contact‐surface unit seating load. in Caesar II software, this gasket y factor is known as gasket seating stress and the values are provided in KPa, N/mm2, or lb/in2 unit. The gasket y-factor is also an important parameter for ASME flange stress calculations and is required as an input.

Importance of Gasket y Factor

The gasket y factor is required to calculate the initial bolt load required under atmospheric temperature conditions when no internal fluid pressure is acting. The gasket must be seated properly using this minimum initial load. The initial bolt load is calculated using the formula Wm2=3.14bGy

Here,

  • G = diameter at the location of gasket load reaction
  • b = effective gasket or joint‐contact‐surface seating width
  • P = internal design pressure

Values of Gasket m and y Factors

The values of gasket m and y factors for some of the most common gasket materials and contact facings are available in Table 2-5.1 of ASME BPVC Sec VIII Div 1 code. However, note that the gasket m and y factor values are only suggested values that are proven to work satisfactorily in actual service and are not mandatory.

Gasket MaterialGasket Factor (m)Seating Stress, y (PSI)Seating Stress, y (Kpa)
Self-energizing types (O rings, metallic elastomer, and other self-sealing types)000
Elastomers without fabric or a high percent of asbestos fiber:   
Below 75A shore durometer0.500
75A or higher shore durometer12001,400
Asbestos with a suitable binder   
1/8″ thick21,60011,000
1/16″ thick2.753,70026,000
1/32″ thick3.56,50045,000
Elastomers with cotton fabric1.254002,800
Elastomers with asbestos fabric   
3 ply2.252,20015,000
2 ply2.52,90020,000
1 ply2.753,70026,000
Vegetable fiber1.751,1007,600
Spiral-wound, asbestos-filled:   
Carbon2.510,00069,000
Stainless, Monel, and nickel alloys310,00069,000
Corrugated metal, mineral fiber inserted, or corrugated metal, jacketed mineral fiber filled   
Soft aluminum2.52,90020,000
Soft copper or brass2.753,70026,000
Iron or soft steel34,50031,000
Monel or 4%-6% chrome3.255,50038,000
Stainless steels and nickel alloys3.56,50045,000
Corrugated metal:   
Soft aluminum2.753,70026,000
Soft copper or brass34,50031,000
Iron or soft steel3.255,50038,000
Monel or 4%-6% chrome3.56,50045,000
Stainless steels and nickel alloys3.757,60052,000
Flat metal, jacketed asbestos filled   
Soft aluminum3.255,50038,000
Soft copper or brass3.56,50045,000
Iron or soft steel3.757,60052,000
Monel3.58,00055,000
4%-6% chrome3.759,00062,000
Stainless steels and nickel alloys3.759,00062,000
Grooved metal   
Soft aluminum3.255,50038,000
Soft copper or brass3.56,50045,000
iron or soft steel3.757,60052,000
Iron or 4%-6% chrome3.759,00062,000
Stainless steels and nickel alloys4.2510,10070,000
Solid flat metal   
Soft aluminum48,80061,000
Soft copper or brass4.7513,00090,000
Iron or soft steel5.518,000124,000
Monel or 4%-6% chrome621,800150,000
Stainless steels and nickel alloys6.526,000180,000
Ring joint   
Iron or soft steel5.518,000124,000
Monel or 4-6% chrome621,800150,000
Stainless steels and nickel-base alloys6.526,000180,000
Gasket m and y factor values

Anup Kumar Dey

I am a Mechanical Engineer turned into a Piping Engineer. Currently, I work in a reputed MNC as a Senior Piping Stress Engineer. I am very much passionate about blogging and always tried to do unique things. This website is my first venture into the world of blogging with the aim of connecting with other piping engineers around the world.

One thought on “Importance of Gasket m and y Factors

  1. Ingeniero saludes desde colombia quiero mejorar mis conocimientos en tubería Piping soy qaqc Dios lo bendiga Ingeniero y en lo pueda enseñar o ser enseñado.

Leave a Reply to Manuel Díaz Rojas Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts