What is a Miter Bend? Design Formulas for Miter Bend Calculation

In the Piping and Pipeline Engineering field, Miter Bend plays an important role because standard Elbows are not easily available and economical for larger pipe sizes. The site Engineer or the Fabrication supervisor is responsible for the perfect delivery of the joints made for the miter bend.
This article will provide detailed calculation procedures for finding out the required dimensions, angles of cut, and weight of the pipe.

What is a Miter Bend?

A Miter Bend or Miter Elbow is prepared by mitering (angle cutting) and welding pipe ends of the cut pieces, usually at 45° and 90° to form a corner. There are two types of miter bend, one non-perpendicular bend & another is 3-D bend. Miter Elbow/Bend is made from miter-cut pieces of pipe. The Miter pieces also called gores, There are two end gores and two middle gores in a 4-piece Miter bend.

Miter Bend/Elbow
Fig. 1: Miter Bend/Elbow

Miter Bend as per ASME B31.3

ASME B31.3 defined miter bend as follows:

A miter bend is a piping or pipeline bend where two or more straight pipe sections are joined in a plane bisecting the angle of the junction that produces a directional change of more than 3 degrees. If the angular offset is 3 degrees or less, the design consideration as per miter bend is not required.

The pressure design of mitered bends is covered in clause 304.2 of ASME B31.3.

Limitations of Miter Bend Applications as per ASME B31.3

  • For normal fluid service, the miter bend can be used but the maximum allowable pressure limits provided in Equations 4a, 4b, and 4C must have to be satisfied.
  • For category D fluid service, a mitered bend can be used when the single joint makes a direction change greater than 45 degrees.
  • For severe cyclic conditions, miter bend can only be used when the direction change angle is 22.5 degrees or less.
  • For high-pressure piping systems, the use of miter bends is not permitted.

Standards Associated with Miter Bend

  • AWWS (American Water Work Association): For sizing and the number of cuts/miter.
  • ASME B16.9: For end preparation of the miters
  • ASME B31.3: For pressure design
READ  Dry Gas Sealing Systems

Note: According to ASME B31.3, the number of miters is restricted to a maximum of 5.

Features of Miter Bends

  • Miter bends are not standard pipe fittings but fabricated piping components.
  • It is also called a fabricated bend or mitered elbow.
  • Highly skilled welders and fitters are required for perfect miter bend preparation.
  • Used mainly in general services (category “D” fluid).
  • If used in process lines then above 14” pipe size.
  • Used above 6” for utility lines.
  • Miter bend can be fabricated with 2, 3, 4, & 5 miters.
  • The number of cuts will be a maximum of 5.
  • The miter thickness is usually different from the parent pipe thickness.
  • The radius of miter bends can be 1D, 1.5D, 2D, 3D, 5D, 10D, or Customized per the application requirement.

Note:
1.
The number of miters will be decided according to the pressure and temperature of the line.
2. Application size range can vary from company to company.

Mitered bends are considered in piping applications when standard elbows are not easily available in the required schedule and the cost becomes too high. These are usually the last choice for every project.

Limitations of Miter Bend

There are certain limitations of miter bends as listed below:

  • Poor strength as the number of weld joints is higher.
  • Higher pressure drop.
  • Higher turbulence.
  • Used mostly for low-pressure piping systems only.
  • Higher risk of corrosion because of more numbers of weld joints.
  • Less strength.
  • Not suitable for pigging.
  • High-skilled manpower is required.
  • Not economical for lower line sizes.
  • It is not suitable for pigging operations.

Advantages of Miter Bend

Miter elbows provide certain benefits like

  • Low cost.
  • No thinning required
  • It can be made at the site or in the workshop.

Inputs Required for Miter Bend Calculation

Pipe/Line SizeSchedule NumberMaterial of Construction or Material TypeBend AngleNumber of CutRadius of Bend
8″SCH 120CS (Carbon Steel)9032.5 D
Table No. 1
Note: D = Pipe/Line size

Steps for Calculation

Step-1: Write down the available data(refer to Table No. 1)

We have,

READ  Emergency Response Procedures and Measures for Process Units

D = 8”,     OD (Outer Diameter) of pipe =  219 mm
Schedule- SCH120
Material- CS (Carbon Steel)
Bend Angle = 90°
No. of cuts = 4
R = 2.5 D = 2.5*8*25.4 = 508 mm

Step-2: As per the number of cuts, Sketch the drawing as below (refer to Fig. 2)

Sketch of Miter Bend for Calculation
Fig. 2: Sketch of Miter Bend for Calculation

Step-3: Find the Angle of the Cut (refer to Fig. 2 for all the steps)

We know,

Step-4: Find the Center Line Length (CL1) of the First Miter

We know from Pythagoras’s formula,

Important Note:

  1. The first and last miter always will be of the same length at each point.
  2. Except for the last miter, all the miter’s length will be double of the first miter at every point.

Therefore,

            CL2 = CL1 * 2 = 272 mm
            CL
= CL1 * 2 = 272 mm
            CL4 = CL1 = 136 mm

Step-5: Calculate the Inside and Outside Radius (IR & OR) of the bend.

We know from Fig. 2,

Step-6: Calculate the Inside Length (IL1) of the First Miter.

We know from Pythagoras formula,

Therefore,

            IL2 = IL1 * 2 = 214 mm
            IL
= IL1 * 2 = 214 mm
            IL4 = IL1 = 107 mm

Step-7: Find out the Outside Length (OL1) of the First Miter

We know from Pythagoras’s formula,

Therefore,

            OL2 = OL1 * 2 = 330 mm
            OL
= OL1 * 2 = 330 mm
            OL4 = OL1 = 165 mm

Step-8: Find the “Length of Pipe required” for the Miter Bend.

Length of pipe required = CL1 + Cutting allowance + CL2 + Cutting allowance + CL3 + Cutting allowance + CL4
Note- Cutting allowance depends upon the cutting method used, we are assuming 5 mm, refer to Fig. 3.

Thus,
         L = 136+5+272+5+272+5+136
        L = 831 mm

Calculated Dimensions for Miter Bend
Fig. 3: Calculated Dimensions for Miter Bend

Step-9: Calculate the Weight of the Pipe.

Check the Plain End Mass in the code book under the code “ASME B36.10 for 8” SCH 120 Pipe (refer to Fig. 4).

Part of Table 1 of ASME B 36.10M-2015
Fig. 4: Part of Table 1 of ASME B 36.10M-2015

Plain End mass is given 90.44 kg/m as per ASME B 36.10 M
Now,
find the weight using the following formula-

Weight of the Pipe = Plain End Mass * Length of Pipe ( in meters)

Weight (W) = 90.44 * 0.831 = 75 kg.

READ  Heat Affected Zone (HAZ): Definition, Causes, Effects, Color Bands, Reduction

Step-10: Get the Cut-back (optional).

Cut-back = CL1 – IL1

Cut-back = 136 – 107 = 29 mm

Maximum Allowable Internal Pressure for Miter Bends

Clause 304.2.3 of ASME B31.3 provides equations for calculating the maximum allowed internal pressure for miter bends. The equations are provided for two types of meter bends:

  • Single Miter Bend, and
  • Multiple Miter Bends

The nomenclature used for the calculations is given in Fig. 5 below:

Nomenclature for Miter Bend
Fig. 5: Nomenclature for Miter Bend

Formulas for Single Miter Bends

For a single miter bend, the code provides two equations based on the angle of cut (θ):

When θ<=22.5 degrees, the maximum allowable internal pressure for a single miter is calculated using the following equation:

On the other hand, when θ>22.5 degrees, the equation for determining the maximum allowable internal pressure is as follows:

Formulas for Multiple Miter Bends

For multiple miter bends, the maximum allowable internal pressure is the lesser value calculated as per equations 4a and 4b below. These equations are valid for θ<=22.5 degrees.

In the above equations:

  • Pm = Maximum allowable internal pressure
  • S = Allowable stress for pipe material
  • E = Quality factor for longitudinal weld joints in pipes
  • W = Weld joint quality reduction factor
  • T = Ordering thickness of the pipe as per the Piping Material Specification
  • c = Sum of mechanical, corrosion, and erosion allowances
  • θ = Angle of the miter cut
  • r2 = Mean radius of the pipe = (D-T)/2
  • D = Outer diameter of the pipe
  • R1 = Radius of the miter bend

Few more useful resources for you.

Piping Elbows vs Bends: A useful literature for piping engineers
Piping Elbow or Bend SIF (Stress Intensification Factor)
Tee Connection: A short literature for piping engineers
Technical requirements for Pipes & Fittings for preparation of Purchase Requisition
“Pipe Coupling”-A short Introduction for the piping professionals
Comparison of Pipe and Tube (Pipe Vs Tube)
Details about Spectacle Blind and Spacers

Rehan Ahmad Khan

I am a graduate in Mechanical Engineering and have worked in automotive aftermarket industry as a Service Engineer before. But there was a spark in me to do creative work which led me to explore opportunities in design world. So, i left my previous job where I had great experience, and decided to enter the energy industry. Later on, enrolled for the “Post Graduation Diploma in Piping Engineering” and through which I got the skills that were required to meet the gap between the industry and my technical skills. I am still exploring this industry and having a great experience. In the process felt to share my knowledge with the other Piping Engineers and as a result, I am here with you.

8 thoughts on “What is a Miter Bend? Design Formulas for Miter Bend Calculation

  1. I am Mechanical Piping & Pipeline Supervisor Engineer with more than 13 years experience relevant in Oil & Gas Indusry EPC Projects.
    I am also Hydraulic Engineer.
    hydrocarbontransportation@gmail.com
    bsaaoui@yahoo.fr
    +213770738270
    +213673316910

  2. Hello, i Wanna ask about number of cut and number of cuts what a different ?
    if i wanna make Elbow 90deg 1200mm for 5 pcs segmented is meaning how many number of cut and cuts ?
    Thanks ,

  3. How to do this calculation below

    The length of pipe to be cut of 3/4″ pipe that has a 90 and a 45 at each end is _______.

  4. Thank you for the information. Can you assist with the infor on determining the number of miters based on the pressure and temperature of the line?

  5. hi.i wanted to know how it is possible to make a cut to the desired degree in the pipe and different places in PDMS.
    for example, cutting a 1 degree in the head of a plain pipe.
    thank you.

Leave a Reply to XU Dongfeng Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts