# Flange Bolt Torque Calculation and Pipe Flange Bolt Torque Chart

Table of Contents

Proper bolt loading is essential for ensuring proper sealing of the flanged joint to avoid leakage problems. This bolt load for gasket sealing and flange seating is provided by Flange Bolt Torque. So Flange Bolt Torque calculation should be done with utmost care for proper functioning of the flanged joints. However, there is no direct method of measuring this load on the gasket, but the applied torque on the flanged bolts can be measured and controlled.

## Equation for Flange Bolt Torque Calculation

Bolt Torque is the twisting or turning force applied to tighten the nut on a bolt. Using a calibrated torque wrench (Manual or Hydraulic Torque Wrench), flange bolt torque can be measured during flange assembly. This torque creates an axial force in the bolt. More torque is applied the nut stretches the bolt more and the load on the gasket increases. Bolt torque is calculated for a flanged assembly using the following equation.

### Applied Torque, T= (k∙f∙d)/12 in FPS Unit

Where:

• T=Torque in ft-lb
• k=Dimensionless nut factor or tightening factor
• f=axial force in pounds
• d=Nominal bolt diameter in inches

In the Metric System,

### Torque Applied, T = (k.d.f)/1000

where

• T = Torque in N-m
• f = Bolt load in N
• d = Bolt diameter in mm
• k=Dimensionless nut factor or tightening factor

## Nut Factor on Flange Bolt Torque calculation

The nut factor or tightening factor (k) is a “modified” friction factor. It is an empirically derived correlation factor that includes the impact of friction. The nut factor depends on various factors including the following:

• Geometric factor – shape or type of threads
• The friction of the nut against the bearing surface of the flange
• Friction between threads of nuts and bolts
• Bolt diameter
• Bolt material
• Assembly temperature, etc.

Because of so many factors, the applied torque between the two fasteners always varies between 20-30%. A small change in the nut factor/tightening factor results in large changes in the gasket load. For same torque values with a 0.1 nut factor would produce twice the axial force as a 0.2 nut factor. That’s why well-lubricated bolts, nuts, and washers are always preferred.

## Pipe Flange Bolt Torque Chart

Even though flange blot toque calculation is possible, they are normally selected from the pipe flange bolt torque chart. The entire bolt pattern shall be tightened at least three times around the flange at 30%, 70%, and 100% of the torque value. For bolt diameters greater than 1.25”, Hydraulic Tensioning is recommended to achieve more uniform gasket stress. The following images provide some typical Pipe flange bolt torque charts.

## Hot Torquing

When the tightening of all bolts of a flanged joint is performed at the
operating temperature, the process is known as Hot Torquing. For flanges that are known to leak at elevated temperatures due to gasket relaxation, the Hot Torqueing method is applied. It is normally performed when the temperature of the flange or the bolts is between 150°C and 230°C, or within 24 hours of a unit start-up if the joint temperature remains below 150°C.

## Flange Bolt Torquing Guidelines

The following guidelines should be followed

• Flanges and Gaskets must be inspected prior to torque application.
• All working surfaces must be cleaned and lubricated properly.
• Gaskets must be new, Re-use is normally not permitted.
• Flange Bolt torquing must be done following the appropriate flange bolt tightening sequence. To know more about flange bolt tightening sequence, Read: Flange Bolt tightening Procedure/Bolt Tightening Steps

Anup Kumar Dey

I am a Mechanical Engineer turned into a Piping Engineer. Currently, I work in a reputed MNC as a Senior Piping Stress Engineer. I am very much passionate about blogging and always tried to do unique things. This website is my first venture into the world of blogging with the aim of connecting with other piping engineers around the world.

## One thought on “Flange Bolt Torque Calculation and Pipe Flange Bolt Torque Chart”

1. Pedro says:

Dear thanks.
Is it possible to include a torque table for non-metallic gasket?, example Garlok
Regard