Spectacle blinds and Spacers are pressure-retaining devices used in the piping/pipeline industry to temporarily or permanently blind (shut) or isolate part of the piping or pipeline system.
A spectacle blind is a forged product and a combination of a flange spade and a ring spacer in one single product.
One end of the spectacle blind will have an opening that allows fluid flow through the pipe during operation and the other end is made solid to block flow during isolation or maintenance time.
One can simply rotate the spectacle blind by 180 degrees to close or open the fluid flow through the piping system.
However, when there is space constraint, Flange spades and ring spacers can be used as separate products.
As one of the two discs is always outside the pipe, one can easily understand if the blind is in an open or closed position.
As it looks like the numeric number Eight or a pair of eyeglasses, a Spectacle blind (Fig. 1 & 2) is also known as a figure 8 blind or figure 8 spectacle blind.
Design Code and Standards for
Spectacle Blind
ASME B16.48 is the governing code for spectacle blind design. This specification provides the dimensions, pressure-temperature ratings, materials, marking, dimensional tolerances, and testing requirements of the Spectacle blind. In general, Blinds are available in sizes NPS 1/2 – NPS 24, and these are installed between ASME B16.5 piping flanges in the 150, 300, 600, 900, 1500, and 2500 Pressure Classes. They are manufactured from steel plates and are available in forged material grades like ASTM A105 (high-temperature carbon), A350 (low-temperature carbon), and ASTM A182 grades (alloy, stainless steel, duplex).
Bigger size spectacle blinds with a diameter of>24 NPS are also available, but these are custom-made. Spectacle blinds of Carbon steel Material are normally manufactured from a single piece of steel, whereas alloy / stainless steel blinds can be produced by welding more pieces together.
DIN Standards for Spectacle blind: DIN 2527, DIN 2566, DIN 2573, DIN 2576, DIN 2641, DIN 2642, DIN 2655, DIN 2656, DIN 2627, DIN 2628, DIN 2629, DIN 2631, DIN 2632, DIN 2633, DIN 2634, DIN 2635, DIN 2636, DIN 2637, DIN 2638, DIN 2673
BS Standards for Spectacle Bild and Spacer: BS 4504, BS 4504, BS1 560, BS 10
Definition of Terms used with
Spectacle Blind
Ring Spacer or Spacer Ring or
Paddle Blank or Paddle Spacer
Spacer Rings are made to match the pipe ID with the same thickness as the “single-blind” that it replaces. During the installation of spacers, the flange and associated piping should be pulled together and a “ring spacer” has to be installed to fill the gap. Normally, a handle is attached to the blank by welding.
Single/ Line Blind or Blank or
Spacer Blind or Flange Spade or Paddle Blind
Single-blind is a positive shut-off device that is generally installed along with a valve so as to prevent accidental flow. In general, they fit inside the bolt circle of mating flanges. However, Plastic, Fiberglass, and Cast Iron, are bolted. Single blinds use standard gaskets.
To differentiate between a spacer and blind in the installed line, the handle of the blank is made solid whereas a formed eye or drilled hole is made for the spacer.
Spectacle Blind
A combination of a ring spacer and a single-blind is used as a spectacle blind. As required they are rotated to serve the purpose. When spectacle blinds become too heavy, a pair of paddle blank and paddle spacer is used instead of a single spectacle blind.
Similar to a “single-blind”, Vapor Blinds are positive sealing devices used for preventing vapor leakage into a pipeline or vessel. Generally, they are thinner compared to single-blind and normally 1/8″ to 5/16″ (3-8mm) thick.
Jack Screw Flanges
For larger-size blinds, Jack Screw Flange is required. Jackscrew help in spreading the flanges and replacing the spacer/blind or turning of spectacle blind.
Use of Spectacle Blind, Spades, and Spacers
As Spectacle Blind, Spades and Spacers belong to the family of pipeline isolation devices, and they are used to provide flexibility during operation and maintenance. Hence, it is required to consider this during the design of the Piping system. Blanks are normally installed in a horizontal line. On average, spectacle blinds are installed on the following
The following spectacle blind symbol is used in P&ID to denote spectacle blind.
Fig. 4: Spectacle blind Symbol
Difference between Spectacle Blind and Spade and Spacers
Spade and Spacer combinedly are comparable to Spectacle Blind. So, a spectacle blind is the combined form of a spade and spacer. For larger pipe sizes the weight of the spectacle blind becomes too heavy. So sometimes, as the requirement arises, a spade or spacer is used. The word “SPADE” or “SPACER” are stamped on the handle of the spade or spacer to clearly indicate what is installed in the line.
In the installed position the handles of the spade and spacers are visible from the outside. The common handle configurations are provided below in Fig. 5
Fig. 5: Spade handle Configurations
Few important Considerations for Spectacle blinds
Spectacle blinds must be accessible from grade, platform, or if below 4500 mm by a portable ladder, or temporary scaffolding.
The proper weight of the Spectacle blind needs to be considered during pipe stress analysis when near the equipment nozzles.
I am a Mechanical Engineer turned into a Piping Engineer. Currently, I work in a reputed MNC as a Senior Piping Stress Engineer. I am very much passionate about blogging and always tried to do unique things. This website is my first venture into the world of blogging with the aim of connecting with other piping engineers around the world.
3 thoughts on “Details about Spectacle Blind and Spacers”
Please clarify: For use of temporary blanks, it is the recommended to use the same material of construction of the mating flanges. Can you site the chapter and verse in the codes
Sir,
We can identify even installed spacer or blind by no. Of holes present on its tale.
If hole quantity is 01, it’s blind and if hole quantity is 02 it’s spacer.
Subsea pipelines play a critical role in transporting oil and gas (hydrocarbon) from remote exploration and production sites to processing facilities and ultimately, consumers. They are essential...
Pipeline block valves are one of the critical components in a pipeline network that ensures the proper management of liquids and gases that it transports. These valves play a crucial role in...
Please clarify: For use of temporary blanks, it is the recommended to use the same material of construction of the mating flanges. Can you site the chapter and verse in the codes
Sir,
We can identify even installed spacer or blind by no. Of holes present on its tale.
If hole quantity is 01, it’s blind and if hole quantity is 02 it’s spacer.
is material marking on spectalcle blind is mandatory?