# Pressure Vessels: Types, Design, Supports, Applications, Materials (PDF)

## What is a Pressure Vessel

A pressure vessel is a closed leak-tight container (normally cylindrical or spherical) designed to hold fluids (i.e, gases or liquids) at a pressure substantially different (higher or lower) from the ambient pressure. They are usually made from carbon steel or stainless steel and assembled from plates by welding method. However, other materials like Aluminium, copper, non-metals, etc also find usage as pressure vessel material in some specific situations. Even though most pressure vessels are basically long cylinders with two heads at both ends, they can take the shape of a sphere or cone.

Examples of some widely used pressure vessels are columns, boilers, separators, knock-out drums, Towers, Bullet Tanks, Reactors, and Heat Exchangers. All these pressure vessels are extensively used in the oil and gas, petroleum refining, and chemical/petrochemical processing industries and power plants have varying operating pressure and temperatures. However, note that an atmospheric storage tank is not a pressure vessel. Fig. 1 shows a typical pressure vessel used in the oil & gas industry.

## What are the Types of Pressure Vessels?

Based on their installation they are classified into the following two groups.

1. Vertical pressure vessel
2. Horizontal Pressure Vessel

Various methods are used to support pressure vessels, like

Types of ends attached to the vessels are

• Dish ends
• Conical ends
• Flat Ends

Fig. 2 shows the general configuration of a pressure vessel.

## Inputs for the Design of Pressure Vessels

The design of pressure vessels must be done with utmost care as these operate under immense pressure. A ruptured pressure vessel can cause serious irreversible harm to mankind and properties. Normally the ASME Sec VIII code governs the design of pressure vessels.

The following inputs are required for pressure vessel design

## Pressure Vessel Design Formula

The basic formula for designing the cylindrical shell is

σ = PD/2t

Therefore,           t = PD/2σ

Where,

•                 t = thickness of the shell
•                 P = internal pressure
•                 D = diameter of the shell
•                 σ = tensile stress

This basic formula is modified in international design codes.

For ASME BPVC Sec VIII, the thickness of the cylinder is calculated by the following formula (Fig. 3)

Where,

• t = thickness of the shell
• P = internal pressure
• R = radius of the cylinder
• S = tensile stress
• E = joint efficiency

Refer to ASME Sec VIII Div 1 for design formulas for all sections of the vessel/cylinder. The following figure provides a typical flow chart for pressure vessel design steps.

## Type of Pressure Vessel Supports

Based on how the pressure vessels are supported, they can be of the following types.

• Vessel Supported on Lug Support (Fig. 5)
• Vessel Supported on Skirt(Fig. 5)
• Vessel Supported on Leg(Fig. 5)
• Vessel Supported on Saddle(Fig. 6)

## Pressure Vessel Parts

A pressure vessel constitute of the following parts

• Nozzles
• Flanges
• Internals
• Baseplate

## Design codes used for Pressure Vessel Design

There are various codes that are used for pressure vessel design, construction, and maintenance purposes. Some of them are listed below:

• EN 13445: The current European Standard, harmonized with the Pressure Equipment Directive (97/23/EC). Extensively used in Europe.
• ASME Code Section VIII, in addition, is supported by Sections II (materials), V (NDT/NDE), and IX (welding). Published by the American Society of Mechanical Engineers.
• ASME Code Section VIII Division 1: US standard, design by the formula. Almost exclusively used in North America, widely used worldwide.
• ASME Code Section VIII Division 2: Alternative Rules, design by analysis.
• ASME Code Section VIII Division 3: Alternative Rules for Construction of High-Pressure Vessel
• BS 5500: Former British Standard, replaced in the UK by EN 13445 but retained under the name PD 5500 for the design and construction of export equipment.
• AD Merkblätter: German standard, harmonized with the Pressure Equipment Directive.
• EN 286 (Parts 1 to 4): European standard for simple pressure vessels (air tanks), harmonized with Council Directive 87/404/EEC.
• BS 4994: Specification for design and construction of vessels and tanks in reinforced plastics.
• IS 2825-1969 (RE1977): code unfired Pressure vessels

## Pressure Vessel Internals

Internals are used to separate the liquid from a mixture of liquid & vapor. Refer to Fig. 6

## Example of Pressure Vessel

Fig. 7 shows a few of the various types of pressure vessels that are normally used in plants.

## Material of Construction of Pressure Vessel

For industrial applications, the following materials are widely used for pressure vessel construction. However custom-made pressure vessel fabrication is possible depending on requirements.

## Applications of Pressure Vessel

Pressure Vessels are most widely used in the following sectors

• Refinery and Petro-chemical
• Fertilizer
• Oil and Gas
• Chemical
• Power Plants

Regular inspection of pressure vessels is very important to avoid pressure vessel failures. API 510 provides guidelines for pressure vessel inspection.

Few more Resources for you.

### Reference

Anup Kumar Dey

I am a Mechanical Engineer turned into a Piping Engineer. Currently, I work in a reputed MNC as a Senior Piping Stress Engineer. I am very much passionate about blogging and always tried to do unique things. This website is my first venture into the world of blogging with the aim of connecting with other piping engineers around the world.

## 20 thoughts on “Pressure Vessels: Types, Design, Supports, Applications, Materials (PDF)”

1. Alberto Jimenez says:

Very good presentaation.  Congratulations.

1. Ndahayo Philipescolari says:

I don’t have much to say about this wonderful piece of work…just blessings….am a chemical engineer in making in my final year

2. plesto says:

Superb presentation..

1. ANDREW DANIEL says:

This was a Perfect Overview….

1. Ndahayo philipe says:

I don’t have much to say about this wonderful piece of work….just blessings only…am a chemical engineer in making …in my final year at campus

Good explanation Mr. Anup sjr, it is too useful for me for preparing for interview in pressure vessel manufacturing company ..thank you !

3. sathish says:

It would be better if you have shown simple vessel design using hand calculation or software

4. Umesh says:

Very good, useful information.

5. Pl.publish article on design of vessels under external pressure with an example. ( Pl clarify whether we can design vessel for partial vacuum?)

6. Jitendra says:

Superb in short.. Excellent present

7. ANDREW DANIEL says:

This was a Perfect Overview….

8. Indrasing Bhimsing Rajput says:

Useful information.

9. MILOS MAJSTOROVIC says:

Simply put, clear and precise, thanks…

10. ANANDAN says:

Clear explanation. And let your journey continue

11. Shailesh Chandrawanshi says:

IT was really Nice. Thank you Sir

12. Noor says:

Thank you a lot

13. Nancy says:

The blog is very informative

14. Centpro says:

I came across your website. It’s awesome.

15. GAURAV BISHT says:

YOUR PRESENTATION IS VERY AWESOME & USEFULL.
WELL DONE.