Pressure Vessels: Types, Design, Supports, Applications, Materials (PDF)

What is a Pressure Vessel

A pressure vessel is a closed leak-tight container (normally cylindrical or spherical) designed to hold fluids (i.e, gases or liquids) at a pressure substantially different (higher or lower) from the ambient pressure. They are usually made from carbon steel or stainless steel and assembled from plates by welding method. However, other materials like Aluminium, copper, non-metals, etc also find usage as pressure vessel material in some specific situations. Even though most of the pressure vessels are basically a long cylinder with two heads at both ends, they can take the shape of a sphere or cone.

Examples of few widely used pressure vessels are columns, boilers, separators, knock out drums, Towers, Bullet Tanks, Reactors, and Heat Exchangers. All these pressure vessels are extensively used in the oil and gas, petroleum refining, and chemical/petrochemical processing industries and power plants have varying operating pressure and temperatures. However, note than an atmospheric storage tank is not a pressure vessel. Fig. 1 shows a typical pressure vessel used in the oil & gas industry.

What are the Types of Pressure Vessels?

Based on their installation they are classified into the following two groups.

  1. Vertical pressure vessel
  2. Horizontal Pressure Vessel

Various methods are used to support pressure vessels, like

  • Lug Support
  • Ring Support
  • Skirt Support
  • Leg Support
  • Saddle Support

Types of end attached to the vessels are

  • Dish ends
  • Conical ends
  • Flat Ends

Fig. 2 shows the general configuration of a pressure vessel.

pressure vessels used in a process plant
Fig. 1: pressure vessels used in a process plant

Inputs for Design of Pressure Vessels

The design of pressure vessels must be done with utmost care as these operate under immense pressure. A ruptured pressure vessel can cause serious irreversible harm to mankind and properties. Normally the ASME Sec VIII code governs the design of pressure vessels.

The following inputs are required for pressure vessel design

  • Internal Design Pressure / External Design Pressure
  • Test Pressure
  • Design temperature
  • Material of constructions
  • Type of support
  • Type of loading (wind load/seismic loading/snow loading)

Pressure Vessel Design Formula

The basic formula for designing the cylindrical shell is

σ = PD/2t

Therefore,           t = PD/2σ


  •                 t = thickness of the shell
  •                 P = internal pressure
  •                 D = diameter of the shell
  •                 σ = tensile stress
General Configuration of a typical pressure Vessel
Fig. 2: General Configuration of a typical pressure Vessel

This basic formula is modified in international design codes.

For ASME Sec VIII, the thickness of the cylinder is calculated by the following formula (Fig. 3)

Formula for calculation of pressure vessel shell thickness
Fig. 3: Formula for calculation of pressure vessel shell thickness


  • t = thickness of the shell
  • P = internal pressure
  • R = radius of cylinder
  • S = tensile stress
  • E = joint efficiency

Refer ASME Sec VIII Div 1 for design formulas for all sections of the vessel/cylinder. The following figure provides a typical flow chart for pressure vessel design steps.

Flow Chart for Pressure Vessel Design Steps
Fig. 4: Flow Chart for Pressure Vessel Design Steps

Type of Pressure Vessel Supports

Based on how the pressure vessels are supported, they can be of the following types.

  • Vessel Supported on Lug Support (Fig. 5)
  • Vessel Supported on Skirt(Fig. 5)
  • Vessel Supported on Leg(Fig. 5)
  • Vessel Supported on Saddle(Fig. 6)
types of pressure vessel supports
Fig. 5: Various types of supports for pressure vessel
Pressure Vessel Supported on Saddle
Fig. 6: Pressure Vessel Supported on Saddle

Pressure Vessel Parts

A pressure vessel constitute of the following parts

  • Shell, head
  • Nozzles
  • Flanges
  • Gaskets
  • Internals
  • Platforms & ladders
  • Skirt or saddles
  • Baseplate

Click here to know more about major pressure vessel parts.

Design codes used for Pressure Vessel Design

There are various codes which are used for pressure vessel design, construction and maintenance purposes. Few of them are listed below:

  • EN 13445: The current European Standard, harmonized with the Pressure Equipment Directive (97/23/EC). Extensively used in Europe.
  • ASME Code Section VIII, in addition, supported by Sections II (materials), V (NDT/NDE), and IX (welding). Published by the American Society of Mechanical Engineers.
  • ASME Code Section VIII Division 1: US standard, design by the formula. Almost exclusively used in North America, widely used worldwide.
  • ASME Code Section VIII Division 2: Alternative Rules, design by analysis.
  • ASME Code Section VIII Division 3: Alternative Rules for Construction of High-Pressure Vessel
  • BS 5500: Former British Standard, replaced in the UK by EN 13445 but retained under the name PD 5500 for the design and construction of export equipment.
  • AD Merkblätter: German standard, harmonized with the Pressure Equipment Directive.
  • EN 286 (Parts 1 to 4): European standard for simple pressure vessels (air tanks), harmonized with Council Directive 87/404/EEC.
  • BS 4994: Specification for design and construction of vessels and tanks in reinforced plastics.
  • IS 2825-1969 (RE1977): code unfired Pressure vessels

Pressure Vessel Internals

Internals are used to separate the liquid from a mixture of liquid & vapour. Refer Fig. 6

Pressure Vessel Internals.
Fig. 6: Pressure Vessel Internals.

Example of Pressure Vessel

Fig. 7 shows a few of the various types of pressure vessels that are normally used in plants.

various types of pressure vessels in industrial use
Fig. 7: Various types of pressure vessels.

Material of Construction of Pressure Vessel

For industrial applications, the following materials are widely used for pressure vessel construction. However custom made pressure vessel fabrication is possible depending on requirements.

  • Carbon steel and Cladding Plates
  • Low and High Alloy Steels
  • Stainless Steel
  • Manganese Steel
  • Duplex Stainless steel
  • Aluminum, Copper, Nickel Alloys
  • Fibre Glass Reinforced Plastic

Applications of Pressure Vessel

Pressure Vessels are most widely used in the following sectors

  • Refinery and Petro-chemical
  • Fertilizer
  • Oil and Gas
  • Chemical
  • Power Plants

Regular inspection of pressure vessels is very important to avoid pressure vessel failures. API 510 provides guidelines for pressure vessel inspection.

Few more Resources for you.

Brief Explanation of Major Pressure Vessel Parts
10 points to keep in mind while using project-specific pressure vessel nozzle load tables during stress analysis
Understanding Pressure and Temperature in the context of Pressure Vessel Design
A video tutorial on “Comprehensive Design Code Coverage for Pressure Vessel and Heat Exchanger Design” by Bentley Institute


Print Friendly, PDF & Email

Anup Kumar Dey

I am a Mechanical Engineer turned into a Piping Engineer. Currently, I work in a reputed MNC as a Senior Piping Stress Engineer. I am very much passionate about blogging and always tried to do unique things. This website is my first venture into the world of blogging with the aim of connecting with other piping engineers around the world.

20 thoughts on “Pressure Vessels: Types, Design, Supports, Applications, Materials (PDF)

    1. I don’t have much to say about this wonderful piece of work…just blessings….am a chemical engineer in making in my final year

    1. I don’t have much to say about this wonderful piece of work….just blessings only…am a chemical engineer in making …in my final year at campus

    2. Good explanation Mr. Anup sjr, it is too useful for me for preparing for interview in pressure vessel manufacturing company ..thank you !

Leave a Reply to plesto Cancel reply

Your email address will not be published.

Recent Posts